Lenovo ThinkServer TD200x Bedienungsanleitung Seite 80
- Seite / 214
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
To remove a hot-swap power supply, do the following:
1. Read the safety information “Safety” on page vii and “Handling static-sensitive
devices” on page 39.
Attention: Static electricity that is released to internal server components
when the server is powered on might cause the server to halt, which might
result in the loss of data. To avoid this potential problem, always use an
electrostatic-discharge wrist strap or other grounding system when you work
inside the server with the power on.
2. Disconnect the power cord from the connector on the back of the power supply
that you are removing.
3. Press the release latch on the power supply 1 and pull the power supply 2
out of the power-supply cage.
4. If you are instructed to return the hot-swap power supply, follow all packaging
instructions, and use any packaging materials for shipping that are supplied to
you.
Installing a hot-swap power supply
If you install or remove a hot-swap power supply, observe the following precautions.
Statement 8:
64 ThinkServer TD200x Types 3719, 3821, 3822, and 3823: Installation and User Guide
- Installation and User Guide 1
- Contents 5
- Contents v 7
- Safety ix 11
- Safety xi 13
- Safety xiii 15
- Chapter 1. Introduction 17
- 1 Model and machine type 18
- Related documentation 19
- Features and technologies 23
- Specifications 26
- Software 27
- EasyStartup 28
- EasyManage 28
- Front view 31
- Operator information panel 32
- EasyLED diagnostics panel 33
- Rear view 40
- System-board LEDs 45
- SAS backplane connectors 49
- Power-supply LEDs 49
- Server power features 50
- Turning on the server 50
- Turning off the server 51
- Installation guidelines 53
- System reliability guidelines 54
- Server components 56
- Opening the bezel 57
- Opening the bezel media door 57
- Removing the left-side cover 58
- 1 Cover release latch 59
- 2 Lock 59
- 3 Left-side cover 59
- Removing the bezel 60
- Installing the bezel 62
- Opening the power-supply cage 63
- 1 Release latch 64
- 2 Hot-swap power supply 64
- 1 Power-supply cage 64
- 2 Power-supply cage handle 64
- Closing the power-supply cage 65
- Turning the stabilizing feet 67
- 1 Optical drive power cable 68
- 3 USB signal cable 68
- 4 Optical drive power cable 68
- 1 Cable for drives 4-7 69
- 3 Cable for drives 0-3 69
- 1 EasyLED cable connector 73
- 2 EasyLED cable 73
- Removing the air baffle 74
- Installing the air baffle 75
- 1 Fan cage assembly 76
- Removing the battery 77
- Installing the battery 78
- 1 Hot-swap power supply 81
- 2 Release latch 81
- 1 Microprocessor 2 VRM 84
- 2 Heat sink 2 84
- 3 VRM connector 84
- 2 Hinge pin 86
- 2 Hinge pins 87
- Removing an adapter 88
- Installing an adapter 88
- 2 Adapter 90
- Removing the DVD drive 91
- 1 EMC shield 93
- 2 Tape drive 93
- 2 Fan-cage assembly 95
- 1 Filler panel 97
- 2 Hard disk drive assembly 97
- 3 Release latch 97
- 4 Drive handle 97
- Removing a memory module 100
- Installing a memory module 101
- Independent channel mode 102
- Memory mirroring mode 102
- 1 DIMM 106
- 2 Retaining clip 106
- 1 Microprocessor 1 107
- 2 Microprocessor 2 108
- 1 Microprocessor 109
- 2 Alignment triangles 109
- 3 Notches 109
- Thermal grease 111
- Removing a hot-swap fan 112
- Installing a hot-swap fan 113
- Completing the installation 113
- Closing the bezel media door 114
- Closing the bezel 114
- Installing the side cover 115
- Connecting the cables 115
- Using the Setup Utility 120
- Starting the Setup Utility 120
- Setup Utility menu choices 120
- Passwords 123
- Power-on password 124
- Administrator password 125
- RAID controllers 126
- Formatting a hard disk drive 128
- Starting the WebBIOS utility 129
- Configuring RAID 131
- Setup and configuration 132
- Updating the firmware 135
- Installation requirements 139
- Installation order 139
- Chapter 7. Troubleshooting 143
- DVD drive problems 144
- General problems 144
- Hard disk drive problems 145
- Intermittent problems 145
- Memory problems 147
- Microprocessor problems 148
- Monitor problems 149
- Optional-device problems 150
- Power problems 152
- Serial port problems 153
- Software problems 154
- Solving power problems 154
- Solving undetermined problems 156
- Event logs 156
- System-event log 158
- POST error codes 159
- User’s Guide on the Web 166
- Diagnostic text messages 191
- Viewing the test log 191
- Diagnostics messages 192
- Before you call 193
- Using the documentation 193
- Calling for service 194
- Using other services 194
- Lenovo product service 195
- Appendix B. Notices 197
- Trademarks 198
- Important notes 198
- Appendix B. Notices 183 199
- Hazardous Substances 200
- Battery return program 201
- Electronic emission notices 202
- Appendix B. Notices 187 203
- Appendix B. Notices 189 205
- Index 193 209
- Index 195 211
- Printed in USA 214
Verwandte Produkte und Handbücher für Computerhardware Lenovo ThinkServer TD200x
(36 Seiten)
(120 Seiten)
(12 Seiten)
(4 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 4.574 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern