Lenovo ThinkServer TD200x Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Computerhardware Lenovo ThinkServer TD200x herunter. Lenovo ThinkServer TD200x User Manual Benutzerhandbuch

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 214
  • Inhaltsverzeichnis
  • FEHLERBEHEBUNG
  • LESEZEICHEN
  • Bewertet. / 5. Basierend auf Kundenbewertungen

Inhaltsverzeichnis

Seite 1 - Installation and User Guide

Installation and User GuideThinkServer TD200xMachine Types: 3719, 3821, 3822, and 3823

Seite 2

Antes de instalar este producto, lea la información de seguridad.Läs säkerhetsinformationen innan du installerar den här produkten.Important:Each caut

Seite 3

6. Close the bezel (see “Closing the bezel” on page 98).Removing a memory module1 DIMM2 Retaining clipTo remove a dual inline memory module (DIMM)

Seite 4

Installing a memory moduleThe following notes describe the types of dual inline memory modules (DIMMs) thatyour server supports and other information

Seite 5 - Contents

v The server supports 1 GB, 2 GB, and 4 GB DIMMs, with a minimum of 1 GB anda maximum of 64 GB of system memory.For 32-bit operating systems only: Som

Seite 6

following illustration shows that the first pair of DIMMs (indicated by ones (1) insidethe boxes) should be installed in DIMM connector 3 on channel 0

Seite 7 - Contents v

1 CPU 12 CPU 2The following table lists the installation sequence for installing DIMMs inmemory-mirroring mode.Table 8. Memory-mirroring mode DIMM

Seite 8

The following illustration shows how to install DIMMs on the system board.Attention: Static electricity that is released to internal server components

Seite 9

1 DIMM2 Retaining clip10. Insert the DIMM into the connector by aligning the edges of the DIMM with theslots at the ends of the DIMM connector. Fi

Seite 10

2. Enter your product number (machine type and model number) or selectServers and Storage from the Select your product list.3. Select Servers and Stor

Seite 11 - Safety ix

2 Microprocessor 2Attention:1. A startup (boot) microprocessor must always be installed in microprocessorsocket 1 on the system board.2. To ensure c

Seite 12

d. Make sure the microprocessor is oriented and aligned and positioned in thesocket before you try to close the lever.9. Install the microprocessor:a.

Seite 13 - Safety xi

Statement 1:DANGERElectrical current from power, telephone, and communication cables ishazardous.To avoid a shock hazard:v Do not connect or disconnec

Seite 14

Attention: Do not touch the thermal grease 1 on the bottom of the heatsink 2 or set down the heat sink after you remove the plastic cover. Touchin

Seite 15 - Safety xiii

d. Slide the rear flange of the heat sink into the opening in the retainerbracket.e. Press down firmly on the front of the heat sink until it is seate

Seite 16

1 Microprocessor2 0.02 mL of thermal grease5. Use the thermal-grease syringe to place nine uniformly spaced dots of 0.02 mLeach on the top of the

Seite 17 - Chapter 1. Introduction

4. Pull outward on the free end of the handle to remove the fan from the server.5. If you are instructed to return the hot-swap fan, follow all packag

Seite 18 - 1 Model and machine type

4. Rotate the top edge of left-side cover toward the server; then, press down onthe cover handle until it clicks into place (“Installing the side cove

Seite 19 - Related documentation

1 Pull pointTo close the bezel, do the following:1. Rotate the left side of the bezel toward the server to the closed position.2. Lock the left-side

Seite 20

1 USB 1 7 Power-error LED2 USB 2 8 dc-power LED3 USB 3 9 ac-power LED4 USB 4 10 Video5 Ethernet 10/100/1000 11 Serial 1 (COM 1)6

Seite 21

For information about configuring the integrated Gigabit Ethernet controller, see“Configuring the Gigabit Ethernet controller” on page 118.Chapter 5.

Seite 22

102 ThinkServer TD200x Types 3719, 3821, 3822, and 3823: Installation and User Guide

Seite 23 - Features and technologies

Chapter 6. Configuring the serverThe following configuration programs come with the server:v Setup UtilityThe Setup Utility (formerly called the Confi

Seite 24

Statement 2:CAUTION:When replacing the lithium battery, use only the battery recommended by themanufacturer. If your system has a module containing a

Seite 25

Table 9. Server configurations and applications for configuring and managing RAIDarrays (continued)Server configurationRAID array configuration(before

Seite 26 - Specifications

Utility, the changes are reflected in the system summary; you cannot changesettings directly in the system summary.– Product DataSelect this choice to

Seite 27 - Software

- Network ConfigurationSelect this choice to view the system management network interface port,the IMM MAC address, the current IMM IP address, and ho

Seite 28 - EasyManage

v User SecuritySelect this choice to set, change, or clear passwords. See “Passwords” for moreinformation.This choice is on the full and limited Setup

Seite 29

password has access to only the limited Setup Utility menu; the user can set,change, and delete the power-on password, if the system administrator has

Seite 30

v Change the position of the power-on password switch (enable switch 2 of thesystem board switch block (SW6)) to bypass the power-on password check (s

Seite 31 - Front view

Using the Boot Selection Menu programThe Boot Selection Menu is used to temporarily redefine the first startup devicewithout changing boot options or

Seite 32 - Operator information panel

Table 10. RAID utilities (continued)RAID configurationutility Description LocationWhere to find moreinformationLSI Logic MPT SetupUtilityFor:v ServeRA

Seite 33 - EasyLED diagnostics panel

v If you install a different type of RAID controller, see the documentation thatcomes with the controller for information about viewing and changing s

Seite 34

8. Exit the Setup Utility.Using the WebBIOS utilityThe WebBIOS configuration utility enables you to create and manage RAIDconfigurations on LSI SAS co

Seite 35

Statement 3:CAUTION:When laser products (such as CD-ROMs, DVD drives, fiber optic devices, ortransmitters) are installed, note the following:v Do not

Seite 36

Creating a storage configuration using the Configuration WizardFollow these steps to start create a storage configuration:1. Click Configuration Wizar

Seite 37

Using the ThinkServer EasyStartup DVDThe ThinkServer EasyStartup DVD simplifies the process of configuring your RAIDcontroller and installing an opera

Seite 38

v Manually remove the drives that you do not want included in your arraybefore you configure your RAID controller through the EasyStartupprogram.This

Seite 39

If you continue to the main program interface, you will have the following selectableoptions:v Compatibility notes: This selection provides informatio

Seite 40 - Rear view

v Start installation: This task starts the actual installation process. First, the diskis prepared using the disk and partition information you specif

Seite 41

Updating the firmwareThe firmware in the server is periodically updated and is available for download onthe Lenovo Support Web site. Go to http://www.

Seite 42

Starting the backup server firmwareThe system board contains a backup copy area for the server firmware. This is asecondary copy of server firmware th

Seite 43

v Power/Reset control (power-on, hard and soft shut down, hard and soft reset,schedule power control)v Alerts (in-band and out-of-band alerting, PET t

Seite 44

Note: Approximately 3 minutes after the server is connected to ac power, thepower-control button becomes active.2. When the prompt <F1> Setup is

Seite 45 - System-board LEDs

Use the command-line interface to issue setup commands. You can save any of thesettings as a file and run the file as a script. The ASU program suppor

Seite 46

Statement 4:≥ 18 kg (39.7 lb.) ≥ 32 kg (70.5 lb.) ≥ 55 kg (121.2 lb.)CAUTION:Use safe practices when lifting.Statement 5:CAUTION:The power control but

Seite 47

5. (For both Windows Server 2003 and 2008) Download Microsoft Web ServicesEnhancement 2.0 Service Pack 3 (LANDesk Process Manager only) from thefollow

Seite 48

4. Select the checkbox next to Web Server (IIS). A dialog box displays theadditional features that are required.5. Click Add Required Features, then c

Seite 49 - Power-supply LEDs

126 ThinkServer TD200x Types 3719, 3821, 3822, and 3823: Installation and User Guide

Seite 50 - Turning on the server

Chapter 7. TroubleshootingThis chapter describes the diagnostic tools that are available to help you solveproblems that might occur in the server.If y

Seite 51 - Turning off the server

DVD drive problemsv Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the parts

Seite 52

Hard disk drive problemsv Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the

Seite 53 - Installation guidelines

Keyboard, mouse, or pointing-device problemsv Follow the suggested actions in the order in which they are listed in the Action column until the proble

Seite 54 - System reliability guidelines

Memory problemsv Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the parts li

Seite 55

Microprocessor problemsv Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the

Seite 56 - Server components

Monitor problemsSome monitors have their own self-tests. If you suspect a problem with yourmonitor, see the documentation that comes with the monitor

Seite 57 - Opening the bezel media door

Statement 8:CAUTION:Never remove the cover on a power supply or any part that has the followinglabel attached.Hazardous voltage, current, and energy l

Seite 58 - Removing the left-side cover

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the parts listing in the Ha

Seite 59 - 3 Left-side cover

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the parts listing in the Ha

Seite 60 - Removing the bezel

Power problemsv Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the parts lis

Seite 61

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the parts listing in the Ha

Seite 62 - Installing the bezel

Software problemsv Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the parts

Seite 63 - Opening the power-supply cage

2. Check for loose cables in the power subsystem. Also check for short circuits, forexample, if a loose screw is causing a short circuit on a circuit

Seite 64 - 2 Power-supply cage handle

Solving undetermined problemsIf the diagnostic tests did not diagnose the failure or if the server is inoperative, usethe information in this section.

Seite 65 - Closing the power-supply cage

v System-event log: This log contains all IMM, POST, and system managementinterrupt (SMI) events. You can view the system-event log through the SetupU

Seite 66

4. Click Downloads and drivers to download firmware updates.If IPMItool is installed in the server, you can use it to view the system-event log.Most r

Seite 67 - Turning the stabilizing feet

POST error codesWhen you turn on the server, it performs a series of tests to check the operation ofthe server components and some optional devices in

Seite 68 - 4 Optical drive power cable

DANGEROverloading a branch circuit is potentially a fire hazard and a shock hazardunder certain conditions. To avoid these hazards, ensure that your s

Seite 69 - 3 Cable for drives 0-3

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the "Parts Listing&quo

Seite 70

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the "Parts Listing&quo

Seite 71

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the "Parts Listing&quo

Seite 72

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the "Parts Listing&quo

Seite 73 - 2 EasyLED cable

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the "Parts Listing&quo

Seite 74 - Removing the air baffle

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the "Parts Listing&quo

Seite 75 - Installing the air baffle

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the "Parts Listing&quo

Seite 76 - 1 Fan cage assembly

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the "Parts Listing&quo

Seite 77 - Removing the battery

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the "Parts Listing&quo

Seite 78 - Installing the battery

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the "Parts Listing&quo

Seite 79

Chapter 1. IntroductionThis Installation and User Guide is intended to use with your Lenovo®ThinkServer™TD200x (Machine Types 3719, 3821, 3822, and 38

Seite 80

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the "Parts Listing&quo

Seite 81 - 2 Release latch

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the "Parts Listing&quo

Seite 82

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the "Parts Listing&quo

Seite 83

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the "Parts Listing&quo

Seite 84 - 3 VRM connector

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the "Parts Listing&quo

Seite 85

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the "Parts Listing&quo

Seite 86 - 2 Hinge pin

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the "Parts Listing&quo

Seite 87 - 2 Hinge pins

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the "Parts Listing&quo

Seite 88 - Installing an adapter

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the "Parts Listing&quo

Seite 89

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the "Parts Listing&quo

Seite 90 - 2 Adapter

1 Model and machine typeImportant: The server keys cannot be duplicated by a locksmith. If you lose them,order replacement keys from the key manufac

Seite 91 - Removing the DVD drive

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the "Parts Listing&quo

Seite 92

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the "Parts Listing&quo

Seite 93 - 2 Tape drive

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the "Parts Listing&quo

Seite 94

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the "Parts Listing&quo

Seite 95 - 2 Fan-cage assembly

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the "Parts Listing&quo

Seite 96

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the "Parts Listing&quo

Seite 97 - 4 Drive handle

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the "Parts Listing&quo

Seite 98

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the "Parts Listing&quo

Seite 99

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the "Parts Listing&quo

Seite 100 - Removing a memory module

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the "Parts Listing&quo

Seite 101 - Installing a memory module

v Danger: These statements indicate situations that can be potentially lethal orextremely hazardous to you. A danger statement is placed just before t

Seite 102 - Memory mirroring mode

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the "Parts Listing&quo

Seite 103

Note: After you exit from the stand-alone memory diagnostic environment, youmust restart the server to access the stand-alone memory diagnosticenviron

Seite 104

To save the DSA log to a file on a diskette or to the hard disk, click Save Log onthe diagnostic programs screen and specify a location and name for t

Seite 105

Appendix A. Getting help and technical assistanceIf you need help, service, or technical assistance or just want more informationabout Lenovo products

Seite 106 - 2 Retaining clip

Calling for serviceDuring the warranty period, you can get help and information by telephone throughthe Customer Support Center.These services are ava

Seite 107 - 1 Microprocessor 1

Service methods and procedures vary by country, and some services might not beavailable in all countries. International Warranty Service is delivered

Seite 108 - 2 Microprocessor 2

180 ThinkServer TD200x Types 3719, 3821, 3822, and 3823: Installation and User Guide

Seite 109 - 3 Notches

Appendix B. NoticesLenovo may not offer the products, services, or features discussed in this documentin all countries. Consult your local Lenovo repr

Seite 110

estimated through extrapolation. Actual results may vary. Users of this documentshould verify the applicable data for their specific environment.Trade

Seite 111 - Thermal grease

Lenovo makes no representation or warranties regarding non-Lenovo products andservices, including but not limited to the implied warranties of merchan

Seite 113 - Completing the installation

4 ThinkServer TD200x Types 3719, 3821, 3822, and 3823: Installation and User Guide

Seite 114 - Closing the bezel

L’etiquette du système respecte la Directive européenne 2002/96/EC en matière deDéchets des Equipements Electriques et Electroniques (DEEE), qui déter

Seite 115 - Connecting the cables

Battery return programThis product may contain a lithium or lithium ion battery. Consult your user manualor service manual for specific battery inform

Seite 116

batteries pour indiquer que la batterie ne doit pas être mise au rebut mais plutôtrécupérée en fin de cycle de vie selon cette norme.In accordance wit

Seite 117

This device complies with Part 15 of the FCC Rules. Operation is subject to thefollowing two conditions: (1) this device may not cause harmful interfe

Seite 118

Dieses Produkt entspricht den Schutzanforderungen der EU-Richtlinie 2004/108/EG(früher 89/336/EWG) zur Angleichung der Rechtsvorschriften über dieelek

Seite 119

Japan Voluntary Control Council for Interference (VCCI) statementTaiwan Class A warning statementPeople’s Republic of China Class A warning statementK

Seite 120 - Setup Utility menu choices

190 ThinkServer TD200x Types 3719, 3821, 3822, and 3823: Installation and User Guide

Seite 121

IndexAac power LED 25adapterboot option 73installing 73PCI bus, identification 73removing 72types and installation information 72administrator passwor

Seite 122

DIMM (continued)removing 84types and installation information 85DIMMsinstallation sequence for memory mirroring 88display problems 133documentation DV

Seite 123 - Passwords

installing (continued)bezel 46DIMM 89DVD drive 76fan-cage assembly 61fans 97hot-swap hard disk drive 83left-side cover 99microprocessor 92power supply

Seite 124 - Power-on password

Chapter 2. Server setup roadmapThe installation process varies depending on the configuration of the server when itwas delivered. In some cases, the s

Seite 125 - Administrator password

Ppasswordadministrator 109power-on 108PCIbus LED 19extender card slots 73slot error LEDs 32slots 72, 73POSTerror codes 143event log 140powerproblems 1

Seite 126 - RAID controllers

switch block 6 switches 28symmetric multiprocessing 9systemevent log 142system boardexternal connectors 27internal connectors 25LED 19LEDs 29system re

Seite 127

196 ThinkServer TD200x Types 3719, 3821, 3822, and 3823: Installation and User Guide

Seite 130

6 ThinkServer TD200x Types 3719, 3821, 3822, and 3823: Installation and User Guide

Seite 131 - Configuring RAID

Chapter 3. What is included with your serverThe TD200x server package includes the server, printed instructions, theThinkServer Documentation DVD, and

Seite 132 - Setup and configuration

– Remotely accessing the server, using the keyboard and mouse from a remoteclient– Mapping the CD or DVD drive, diskette drive, and USB flash drive on

Seite 133

The server supports up to eight or 16 (depending on your model) 2.5-inchhot-swap hard disk drives in the hot-swap bays. With the hot-swap feature, you

Seite 134

Note: As of the date of this document, the Linux operating system does notsupport TOE.SpecificationsThe following information is a summary of the feat

Seite 135 - Updating the firmware

Table 2. Features and specificationsMicroprocessor:v Intel Xeon dual-core or quad-core withintegrated memory controller and Quick PathInterconnect (QP

Seite 136

EasyStartupThe ThinkServer EasyStartup program simplifies the process of your RAIDcontroller and installing supported Microsoft®Windows®and Linux oper

Seite 137

v Integrated Ethernet controllersv Intelligent Platform Management Interface (IPMI) 2.0v Key-lock support for physical securityv Memory change message

Seite 138

ThinkServer TD200x Types 3719, 3821, 3822, and 3823Installation and User Guide

Seite 139 - Installation order

14 ThinkServer TD200x Types 3719, 3821, 3822, and 3823: Installation and User Guide

Seite 140

Chapter 4. Server controls, LEDs, and powerThis section describes the controls and light-emitting diodes (LEDs) and how to turnthe server on and off.F

Seite 141

Power-control button: Press this button to turn the server on and off manually. Apower-control-button shield comes with the server. You can install th

Seite 142

1 System power-on LED2 Hard disk drive activity LED3 System-locator LED4 System-information LED5 System-error LEDv Follow the suggested acti

Seite 143 - Chapter 7. Troubleshooting

1 Server processor bus 8 Power supply2 Microprocessor 9 Fan3 VRM 10 PCI bus4 Microprocessor/memory configuration 11 System board5 Me

Seite 144 - General problems

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the Parts Listing in the Ha

Seite 145 - Intermittent problems

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the Parts Listing in the Ha

Seite 146

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the Parts Listing in the Ha

Seite 147 - Memory problems

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the Parts Listing in the Ha

Seite 148 - Microprocessor problems

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the Parts Listing in the Ha

Seite 149 - Monitor problems

Note: Before using this information and the product it supports, read the general information in Appendix B, “Notices,” on page 181and the Warranty an

Seite 150 - Optional-device problems

Rear viewThe following illustration shows the connectors and LEDs on the rear of the server.1 USB 1 7 Power-error LED2 USB 2 8 dc-power LED3

Seite 151

ac-power LED: Each hot-swap power supply has an ac-power LED and a dc-powerLED. When the ac-power LED is lit, it indicates that sufficient power is co

Seite 152 - Power problems

1 Microprocessor 2 21 Wake on LAN2 System power 22 Battery3 ADV power 23 PCI Express x8 slot 74 Optical power 24 PCI - 32 slot 65 Fr

Seite 153 - Serial port problems

System-board external connectorsThe following illustration shows the external input/output connectors and the NMIbutton on the system board.1 Video

Seite 154 - Solving power problems

Table 3. System-board jumpersJumpernumberJumpername Jumper setting1 JP6 UEFI bootrecoveryv Pins 1 and 2: Normal operation (default).v Pins 2 and 3:

Seite 155

System-board LEDsThe following illustration shows the LEDs on the system board.1 PCI slot 1 error LED 9 Battery error LED2 PCI slot 2 error LED

Seite 156 - Event logs

Express extender card 1, if one is installed.The following illustration shows the LEDs (1 and 2) on the PCI-X extender card,if one is installed.

Seite 157

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the parts listing in the Ha

Seite 158 - System-event log

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the parts listing in the Ha

Seite 159 - POST error codes

SAS backplane connectorsThe following illustration shows the connectors on the SAS backplane.1 Hard disk drive connectors2 Power connector3 Sign

Seite 160

ContentsSafety ...viiChapter 1. Introduction ...1Notices and statements in this document...2R

Seite 161

The following table describes the problems that are indicated by variouscombinations of the power-supply LEDs and the power-on LED on the operatorinfo

Seite 162

provide cooling while the server is connected to power. You can turn on the serverand start the operating system by pressing the power-control button.

Seite 163

v If the operating system stops functioning, you can press and hold thepower-control button for more than 4 seconds to turn off the server.v The IMM c

Seite 164

Chapter 5. Installing optional devices and replacing customerreplaceable unitsThis chapter provides detailed instructions for installing optional hard

Seite 165

devices. However, you must turn off the server before performing any steps thatinvolve removing or installing adapter cables or non-hot-swap optional

Seite 166 - User’s Guide on the Web

v Avoid wearing loose-fitting clothing on your forearms. Button long-sleeved shirtsbefore working inside the server; do not wear cuff links while you

Seite 167

Server componentsThe following illustration shows the major components in the server.1 Cover 14 USB cable/EasyLED diagnosticsassembly2 Rear adap

Seite 168

Opening the bezelImportant: Before you install optional hardware, make sure that the server isworking correctly. If an operating system is installed,

Seite 169

4. From inside of the top section of the bezel door, slide the blue tab up to unlockthe bezel media door; then, grasp the depressed area on the left s

Seite 170

1 Cover release latch2 Lock3 Left-side coverTo remove the cover, do the following:1. Read the safety information that begins on page vii and “In

Seite 171

Removing a hot-swap power supply ...63Installing a hot-swap power supply ...64Installing redundant power supply and fans .

Seite 172

Removing the bezel1 Bezel2 Hinge assembly3 Retention tabsTo remove the bezel, do the following:1. Read the safety information that begins on pag

Seite 173

4. Press the retention tabs 1 on the hinge assembly toward each other and pullthe hinge assembly out of the chassis.Note: The bezel will also diseng

Seite 174

Installing the bezel1 Bezel2 Hinge assembly3 Retention tabsTo install the bezel, do the following:1. Align the hinge assemblies with the hinge h

Seite 175

b. Align the sliding hinge mount 1 with the hinge pin 2 on the hingeassembly 3 on the chassis.c. Press the sliding hinge mount against the hinge

Seite 176

3. Press the release latch on the power supplies and filler panels and pull themout of the power-supply cage.1 Release latch2 Hot-swap power suppl

Seite 177

Closing the power-supply cageTo return the power-supply cage to its closed position, do the following:1. Rotate the power-supply cage back slightly; t

Seite 178

2. Carefully rotate the power-supply cage into the server chassis. The locating tabson the power-supply cage must fit over the corresponding tabs on t

Seite 179

4. Install and lock the left-side cover (see “Completing the installation” on page97).5. Install the hot-swap power supplies.6. Reconnect the external

Seite 180

3. Reinstall the feet 1 in the opposite location. The tab on the feet should extendbeyond the edge of the server.Internal cable routing and connecto

Seite 181

The following illustration shows the internal SAS/SATA cable routing and connectorsfrom the ServeRAID BR10i controller to eight 2.5-inch hard disk dri

Seite 182

Installation order ...123Installing Windows 2003 components on the Core Server...124Installing Windows 2008 32-bit components

Seite 183

The following illustration shows the internal SAS/SATA cable routing and connectorsfrom the ServeRAID BR10i controller to 16 2.5-inch hard disk drives

Seite 184

The following illustration shows the internal SAS/SATA cable routing and connectorsfrom the ServeRAID MR10i or ServeRAID MR10is controllers to eight 2

Seite 185

The following illustration shows the internal SAS power and signal cable routingfrom the hard disk drives to the connectors on the system board.1 SA

Seite 186

The following illustration shows the internal cable routing and connectors from theoperator information panel to the system board.1 Operator informa

Seite 187

Removing the air baffleTo remove the air baffle, do the following:1. Read the safety information that begins on page vii and “Installation guidelines”

Seite 188

Installing the air baffleTo install the air baffle, do the following:1. With the rear (hinged) part of the air baffle 3 lifted up, align the positio

Seite 189

Removing the fan-cage assembly1 Fan cage assembly2 Fan cage assembly release buttonsTo remove the fan-cage assembly, do the following:1. Read the

Seite 190

Installing the fan-cage assembly1 Fan cage assembly2 Fan cage assembly release buttonsTo install the fan-cage assembly, do the following:1. Align

Seite 191 - Viewing the test log

6. Locate the battery on the system board (see “System-board internal connectors”on page 25).7. Remove the battery:a. Use one finger to push the batte

Seite 192 - Diagnostics messages

To install the replacement battery, do the following:1. Follow any special handling and installation instructions that come with thereplacement batter

Seite 193 - Using the documentation

Avis de conformité à la réglementation d’Industrie Canada ...187Australia and New Zealand Class A statement ...187United Kingdom telecomm

Seite 194 - Using other services

To remove a hot-swap power supply, do the following:1. Read the safety information “Safety” on page vii and “Handling static-sensitivedevices” on page

Seite 195 - Lenovo product service

CAUTION:Never remove the cover on a power supply or any part that has the followinglabel attached.Hazardous voltage, current, and energy levels are pr

Seite 196

5. Connect one end of the power cord for the new power supply into the connectoron the back of the power supply; then, connect the other end of the po

Seite 197 - Appendix B. Notices

1 Release latch2 Hot-swap power supply5. Remove the power supply filler from the second power supply bay.6. Slide the new power supply partially i

Seite 198 - Important notes

Removing a voltage regulator module1 Microprocessor 2 VRM2 Heat sink 23 VRM connectorTo remove a voltage regulator module (VRM), do the followin

Seite 199 - Appendix B. Notices 183

Installing a voltage regulator module1 Microprocessor 2 VRM2 Heat sink 23 VRM connectorTo install a voltage regulator module, do the following:1

Seite 200 - Hazardous Substances

Removing the rear adapter retention bracket1 Rear adapter retention bracket2 Hinge pinTo remove the rear adapter-retention bracket, do the followi

Seite 201 - Battery return program

Installing the rear adapter retention bracket1 Rear adapter retention bracket2 Hinge pinsTo install the rear adapter retention bracket, do the fol

Seite 202 - Electronic emission notices

Removing an adapter1 Rear adapter retention bracket2 Adapter3 Front adapter retention bracketTo remove an adapter, do the following:1. Read the

Seite 203 - Appendix B. Notices 187

v Locate the documentation that comes with the adapter and follow thoseinstructions in addition to the instructions in this section. If you must chang

Seite 204

SafetyBefore installing this product, read the Safety Information.Antes de instalar este produto, leia as Informações de Segurança.Pred instalací toho

Seite 205 - Appendix B. Notices 189

3. See the documentation that comes with the adapter for any cabling instructionsand information about jumper or switch settings. (It might be easier

Seite 206

Attention: Incomplete insertion might cause damage to the system board orthe adapter.8. Connect any needed cables to the adapter.If you have other dev

Seite 207

Installing a DVD (optical) driveTo install a DVD (optical) drive 1, do the following:1. Read the safety information that begins on page vii and “Ins

Seite 208

Removing an optional tape drive1 EMC shield2 Tape driveTo remove an optional tape drive, do the following:1. Read the safety information that begi

Seite 209 - Index 193

Installing a USB or SATA tape driveThe server supports USB and SATA tape drives. When you install a tape drive, besure to connect the internal tape ca

Seite 210

1 Fan-cage assembly release buttons2 Fan-cage assemblya. Press the fan-cage release latches on the top and bottom of the fan cagetoward the sides

Seite 211 - Index 195

14. If the tape drive came with screws, secure the drive to the server chassis,using the supplied screws.1 SATA optical drive power connector2 USB

Seite 212

Removing a 2.5-inch hot-swap hard disk drive1 Filler panel2 Hard disk drive assembly3 Release latch4 Drive handleTo remove a hot-swap hard dis

Seite 213

– On models with eight hard disk drives, the top bays are numbered 0 through 7(from right to left)– On models with 16 hard disk drives, the top bays a

Seite 214 - Printed in USA

1 Filler panel2 Hard disk drive assembly3 Release latch4 Drive handleTo install a hot-swap hard disk drive, do the following:1. Read the safet

Kommentare zu diesen Handbüchern

Keine Kommentare