Lenovo TD100 Bedienungsanleitung Seite 225
- Seite / 254
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
v Follow the suggested actions in the order in which they are listed in the Action column until the problem
is solved.
v See Chapter 3, “Parts listing, TD100 Types 6398, 6399, 6419, 6429, 4203, and 4206,” on page 25 to
determine which components are customer replaceable units (CRU) and which components are field
replaceable units (FRU).
v If an action step is preceded by “(Trained service technician only),” that step must be performed only by a
trained service technician.
System-error log message Action
Failure reading an I2C device, possible bus
failure
1. Reseat the following components:
a. AC power cords
b. Hot-swap power supplies (if any are installed)
c. (Trained service technician only) Power-supply cables on
the system board
2. (Trained service technician only) Replace the system board.
Fan x Failure
1. Make sure that fan x is not obstructed.
2. Reseat the fan x cable.
3. Replace fan x.
Fan x Outside Recommended Speed
1. Make sure that fan x is not obstructed.
2. Reseat the fan x cable.
3. Replace fan x.
Flash of x by y via z was successful...w Information only.
Flash of x via z failed for user z...z Information only.
Flash succeeded for x (address: y) Information only.
Hard Drive x Fault
1. Run the diagnostics programs.
2. Replace hard disk drive x.
3. Replace the following component, depending on the server
model:
v Hot-swap models: SAS/SATA backplane
v Simple-swap: Hard disk drive x cable
Hard drive x removal detected. Reseat hard disk drive x.
Internal Error CPU Fault Information only. If the message remains:
1. (Trained service technician only) Reseat the microprocessor.
2. (Trained service technician only) Replace the microprocessor.
Invalid userid or password received. Userid is w,
x, y, z
Information only.
LAN: Command Mode tamper triggered.
Possible break in attempt
Information only.
LAN: Telnet tamper triggered. Possible break in
attempt
Information only.
LAN: Web Server tamper delay triggered.
Possible break-in attempt
Information only.
LAN: Ethernet interface is no longer active Information only.
LAN: Ethernet interface is now active Information only.
No ISMP Gateway defined for the interconnect
network. RSA x is Assuming the Gateway
Information only.
OS Watchdog response disabled by x Information only.
Chapter 5. Diagnostics 207
- Contents 5
- Contents v 7
- Safety ix 11
- Safety statements 12
- Safety xi 13
- Safety xiii 15
- >82 kg (180 lb) 16
- Safety xv 17
- Chapter 1. Introduction 19
- Front view 22
- Chapter 1. Introduction 5 23
- Rear view 25
- Chapter 1. Introduction 9 27
- Chapter 1. Introduction 11 29
- System-board LEDs 31
- System-board switches 32
- Updating the firmware 33
- Configuring the server 33
- SATA (some models) RAID 35
- Using RAID Manager 38
- Configuring the controller 39
- Viewing the configuration 40
- Using the Boot Menu program 41
- 4203, and 4206 43
- Replaceable server components 44
- Power cords 79
- Installation guidelines 91
- System reliability guidelines 92
- Removing the bezel 94
- Replacing the bezel 95
- Removing the side cover 96
- Installing the side cover 97
- Turning the stabilizing feet 98
- Removing an adapter 99
- Installing an adapter 100
- 2 Adapter 101
- 1 Bay 1 5 Bay 5 103
- 2 Bay 2 6 Bay 6 103
- 3 Bay 3 7 Bay 7 103
- 4 Bay 4 103
- Removing a CD or DVD drive 104
- Installing a CD or DVD drive 105
- 2 Optional drive 106
- 3 Optional drive rails 106
- 1 EMC shield 106
- 1 Hard disk drive 107
- 2 Drive tray 107
- 1 Power supply filler 114
- 2 Release latch 114
- 3 Power supply 114
- Removing a memory module 115
- Installing a memory module 116
- Removing a hot-swap fan 122
- Installing a hot-swap fan 123
- Fan cage assembly 126
- Removing the battery 132
- Installing the battery 132
- Removing the RAID-8k adapter 134
- 1 SAS/SATA backplane 2 137
- DIMM air duct 138
- Installing the DIMM air duct 139
- Removing and replacing FRUs 143
- 1 Locator pins 147
- 2 Spring-release latches 147
- 3 Hard disk drive backplate 147
- 2 Hard disk drive backplane 149
- Power supply 152
- 1 Heat sink locking lever 156
- 2 Microprocessor 156
- 3 Heat sink 156
- Microprocessor 157
- (fully open) 157
- 1 Heat-sink locking lever 158
- 3 Heat-sink 158
- Thermal grease 159
- 0.01 mL of 159
- Removing the system board 161
- 1 Handle 162
- 2 Release lever 162
- 3 Handle 162
- Installing the system board 163
- Light path 164
- Release Tab 164
- Chapter 5. Diagnostics 165
- POST beep codes 166
- Chapter 5. Diagnostics 149 167
- Chapter 5. Diagnostics 151 169
- No-beep symptoms 170
- Error logs 171
- POST error codes 173
- Chapter 5. Diagnostics 157 175
- Chapter 5. Diagnostics 159 177
- Chapter 5. Diagnostics 161 179
- Chapter 5. Diagnostics 163 181
- Chapter 5. Diagnostics 165 183
- Chapter 5. Diagnostics 167 185
- Chapter 5. Diagnostics 169 187
- Checkout procedure 188
- About the checkout procedure 188
- Chapter 5. Diagnostics 171 189
- Troubleshooting tables 190
- CD or DVD drive problems 190
- Diskette drive problems 191
- General problems 192
- Hard disk drive problems 192
- Intermittent problems 193
- Memory problems 195
- Microprocessor problems 196
- Monitor or video problems 196
- Chapter 5. Diagnostics 179 197
- Optional-device problems 199
- Power problems 200
- Serial port problems 201
- ServerGuide problems 202
- Software problems 202
- Chapter 5. Diagnostics 185 203
- Error LEDs 204
- Power-supply LEDs 205
- Chapter 5. Diagnostics 189 207
- Diagnostic text messages 208
- Viewing the test log 208
- Diagnostic error codes 209
- Chapter 5. Diagnostics 193 211
- Chapter 5. Diagnostics 195 213
- Chapter 5. Diagnostics 197 215
- Chapter 5. Diagnostics 199 217
- Chapter 5. Diagnostics 201 219
- Chapter 5. Diagnostics 203 221
- System-error log messages 223
- Chapter 5. Diagnostics 207 225
- Chapter 5. Diagnostics 209 227
- Chapter 5. Diagnostics 211 229
- Solving SCSI problems 231
- Solving power problems 231
- Solving undetermined problems 233
- Calling Lenovo for service 234
- Before you call 235
- Using the documentation 235
- Calling for service 236
- Using other services 236
- Lenovo Taiwan product service 237
- Appendix. Notices 239
- Trademarks 240
- Important notes 240
- Appendix. Notices 223 241
- Battery return program 242
- Electronic emissions notices 243
- Appendix. Notices 227 245
- Index 231 249
- Index 233 251
- Part Number: 46U0860 254
- Printed in USA 254
- (1P) P/N: 46U0860 254
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 1.255 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern