Lenovo TD100 Bedienungsanleitung Seite 129
- Seite / 254
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Installing the front USB connector assembly
To install the front USB connector assembly, complete the following steps.
1. Carefully feed the front USB cable through the opening in the front of the
chassis.
2. Squeeze the spring clips on the sides of the front USB connector assembly and
insert the assembly into the housing through the back of the housing.
3. Place the bottom edge of the housing into the bottom of the opening in the
chassis; then, tilt the top of the housing into position until it clicks into place.
4. Reroute and connect the front USB cable to the system board (see
“System-board internal connectors” on page 10 for the location of the front USB
connector).
5. Replace the bezel (see “Replacing the bezel” on page 77).
6. Install the side cover (see “Installing the side cover” on page 79).
7. Lock the side cover.
8. Reconnect the external cables and power cords; then, turn on the attached
devices and turn on the server.
Removing the rear adapter retention bracket
To remove the rear adapter-retention bracket, complete the following steps:
1. Turn off the server and all attached devices; then, disconnect all power cords
and external cables.
2. Unlock and remove the side cover (see “Removing the side cover” on page 78).
3. Remove all adapters and place the adapters on static-protective surface.
Note: You might find it helpful to note where each adapter is installed before
removing the adapters.
4. Release the rear adapter-retention bracket 1 by pressing up on the rear
adapter retainer bracket and rotate the bracket partially toward the closed
position.
5. Grasp the bracket on one side at the hinge point and pull outward (while
rotating the bracket slightly toward the front of the server) until the bracket is
free of the hinge pin 2; then, push the bracket in the opposite direction to
release the other side of the bracket and remove adapter guide from the server.
Chapter 4. Removing and replacing server components 111
- Contents 5
- Contents v 7
- Safety ix 11
- Safety statements 12
- Safety xi 13
- Safety xiii 15
- >82 kg (180 lb) 16
- Safety xv 17
- Chapter 1. Introduction 19
- Front view 22
- Chapter 1. Introduction 5 23
- Rear view 25
- Chapter 1. Introduction 9 27
- Chapter 1. Introduction 11 29
- System-board LEDs 31
- System-board switches 32
- Updating the firmware 33
- Configuring the server 33
- SATA (some models) RAID 35
- Using RAID Manager 38
- Configuring the controller 39
- Viewing the configuration 40
- Using the Boot Menu program 41
- 4203, and 4206 43
- Replaceable server components 44
- Power cords 79
- Installation guidelines 91
- System reliability guidelines 92
- Removing the bezel 94
- Replacing the bezel 95
- Removing the side cover 96
- Installing the side cover 97
- Turning the stabilizing feet 98
- Removing an adapter 99
- Installing an adapter 100
- 2 Adapter 101
- 1 Bay 1 5 Bay 5 103
- 2 Bay 2 6 Bay 6 103
- 3 Bay 3 7 Bay 7 103
- 4 Bay 4 103
- Removing a CD or DVD drive 104
- Installing a CD or DVD drive 105
- 2 Optional drive 106
- 3 Optional drive rails 106
- 1 EMC shield 106
- 1 Hard disk drive 107
- 2 Drive tray 107
- 1 Power supply filler 114
- 2 Release latch 114
- 3 Power supply 114
- Removing a memory module 115
- Installing a memory module 116
- Removing a hot-swap fan 122
- Installing a hot-swap fan 123
- Fan cage assembly 126
- Removing the battery 132
- Installing the battery 132
- Removing the RAID-8k adapter 134
- 1 SAS/SATA backplane 2 137
- DIMM air duct 138
- Installing the DIMM air duct 139
- Removing and replacing FRUs 143
- 1 Locator pins 147
- 2 Spring-release latches 147
- 3 Hard disk drive backplate 147
- 2 Hard disk drive backplane 149
- Power supply 152
- 1 Heat sink locking lever 156
- 2 Microprocessor 156
- 3 Heat sink 156
- Microprocessor 157
- (fully open) 157
- 1 Heat-sink locking lever 158
- 3 Heat-sink 158
- Thermal grease 159
- 0.01 mL of 159
- Removing the system board 161
- 1 Handle 162
- 2 Release lever 162
- 3 Handle 162
- Installing the system board 163
- Light path 164
- Release Tab 164
- Chapter 5. Diagnostics 165
- POST beep codes 166
- Chapter 5. Diagnostics 149 167
- Chapter 5. Diagnostics 151 169
- No-beep symptoms 170
- Error logs 171
- POST error codes 173
- Chapter 5. Diagnostics 157 175
- Chapter 5. Diagnostics 159 177
- Chapter 5. Diagnostics 161 179
- Chapter 5. Diagnostics 163 181
- Chapter 5. Diagnostics 165 183
- Chapter 5. Diagnostics 167 185
- Chapter 5. Diagnostics 169 187
- Checkout procedure 188
- About the checkout procedure 188
- Chapter 5. Diagnostics 171 189
- Troubleshooting tables 190
- CD or DVD drive problems 190
- Diskette drive problems 191
- General problems 192
- Hard disk drive problems 192
- Intermittent problems 193
- Memory problems 195
- Microprocessor problems 196
- Monitor or video problems 196
- Chapter 5. Diagnostics 179 197
- Optional-device problems 199
- Power problems 200
- Serial port problems 201
- ServerGuide problems 202
- Software problems 202
- Chapter 5. Diagnostics 185 203
- Error LEDs 204
- Power-supply LEDs 205
- Chapter 5. Diagnostics 189 207
- Diagnostic text messages 208
- Viewing the test log 208
- Diagnostic error codes 209
- Chapter 5. Diagnostics 193 211
- Chapter 5. Diagnostics 195 213
- Chapter 5. Diagnostics 197 215
- Chapter 5. Diagnostics 199 217
- Chapter 5. Diagnostics 201 219
- Chapter 5. Diagnostics 203 221
- System-error log messages 223
- Chapter 5. Diagnostics 207 225
- Chapter 5. Diagnostics 209 227
- Chapter 5. Diagnostics 211 229
- Solving SCSI problems 231
- Solving power problems 231
- Solving undetermined problems 233
- Calling Lenovo for service 234
- Before you call 235
- Using the documentation 235
- Calling for service 236
- Using other services 236
- Lenovo Taiwan product service 237
- Appendix. Notices 239
- Trademarks 240
- Important notes 240
- Appendix. Notices 223 241
- Battery return program 242
- Electronic emissions notices 243
- Appendix. Notices 227 245
- Index 231 249
- Index 233 251
- Part Number: 46U0860 254
- Printed in USA 254
- (1P) P/N: 46U0860 254
Whirlpool HDW 1011 WG podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Pralki Whirlpool HDW 1011 WG.
Dostarczamy 1 pdf podręczników Whirlpool HDW 1011 WG do pobrania za darmo według typów dokumentów: Instrukcja Obsługi
Kommentare zu diesen Handbüchern