Lenovo LF80565QH0254M Datenblatt Seite 87

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 142
  • Inhaltsverzeichnis
  • LESEZEICHEN
  • Bewertet. / 5. Basierend auf Kundenbewertungen
Seitenansicht 86
Document Number: 318080-002 87
Signal Definitions
5 Signal Definitions
5.1 Signal Definitions.
Table 5-1. Signal Definitions (Sheet 1 of 8)
Name Type Description Notes
A[39:3]# I/O A[39:3]# (Address) define a 2
40
-byte physical memory address space. In sub-phase
1 of the address phase, these pins transmit the address of a transaction. In sub-
phase 2, these pins transmit transaction type information. These signals must
connect the appropriate pins of all agents on the Intel
®
Xeon
®
Processor 7200 Series
and 7300 Series FSB. A[39:3]# are protected by parity signals AP[1:0]#. A[39:3]#
are source synchronous signals and are latched into the receiving buffers by
ADSTB[1:0]#.
On the active-to-inactive transition of RESET#, the processors sample a subset of the
A[39:3]# pins to determine their power-on configuration. See Section 7.1.
A20M# I If A20M# (Address-20 Mask) is asserted, the processor masks physical address bit 20
(A20#) before looking up a line in any internal cache and before driving a read/write
transaction on the bus. Asserting A20M# emulates the 8086 processor's address
wrap-around at the 1 MB boundary. Assertion of A20M# is only supported in real
mode.
A20M# is an asynchronous signal. However, to ensure recognition of this signal
following an I/O write instruction, it must be valid along with the TRDY# assertion of
the corresponding I/O write bus transaction.
ADS# I/O ADS# (Address Strobe) is asserted to indicate the validity of the transaction address
on the A[39:3]# pins. All bus agents observe the ADS# activation to begin parity
checking, protocol checking, address decode, internal snoop, or deferred reply ID
match operations associated with the new transaction. This signal must be connected
to the appropriate pins on all Intel
®
Xeon
®
Processor 7200 Series and 7300 Series
FSB agents.
ADSTB[1:0]# I/O Address strobes are used to latch A[39:3]# and REQ[4:0]# on their rising and falling
edge. Strobes are associated with signals as shown below.
AP[1:0]# I/O AP[1:0]# (Address Parity) are driven by the requestor one common clock after
ADS#, A[39:3]#, REQ[4:0]# are driven. A correct parity signal is electrically high if
an even number of covered signals are electrically low and electrically low if an odd
number of covered signals are electrically low. This allows parity to be electrically
high when all the covered signals are electrically high. AP[1:0]# should connect the
appropriate pins of all Intel
®
Xeon
®
Processor 7200 Series and 7300 Series FSB
agents. The following table defines the coverage for these signals.
BCLK[1:0] I The differential bus clock pair BCLK[1:0] (Bus Clock) determines the FSB frequency.
All processor FSB agents must receive these signals to drive their outputs and latch
their inputs.
All external timing parameters are specified with respect to the rising edge of BCLK0
crossing V
CROSS
.
Signals Associated Strobes
REQ[4:0],
A[37:36,16:3]#
ADSTB0#
A[39:38, 35:17]# ADSTB1#
Request Signals Subphase 1 Subphase 2
A[39:24]# AP0# AP1#
A[23:3]# AP1# AP0#
REQ[4:0]# AP1# AP0#
Seitenansicht 86
1 2 ... 82 83 84 85 86 87 88 89 90 91 92 ... 141 142

Kommentare zu diesen Handbüchern

Keine Kommentare