ThinkCentreHardware Installation and Replacement GuideMachine Types 6019, 6064, 6066, 6067, 6072, 6073, 6077, 6078, 6087,6088, 9181, 9196, 9325, 9330,
2 ThinkCentre Hardware Installation and Replacement Guide
Chapter 2. Overview This guide provides information about replacing Customer Replaceable Units (CRUs). This guide does not include proc
Handling static-sensitive devices Do not open the static-protective package containing the new part until the defective part has been
Locations This chapter provides illustrations to help locate the various connectors, controls, and components of the computer. Locating
Locating connectors on the rear of your computer Figure 2 shows the location of connectors on the rear of your computer. Some conn
Connector Description USB connectors Used to attach a device that requires a Universal Serial Bus (USB) connection, such as a USB k
Locating components To open the computer cover, see “Opening the cover” on page 12. Figure 3 shows the location of the various com
Identifying parts on the system board Figure 4 shows the location of parts on the system board. 1 4 - Pin power connector 9
10 ThinkCentre Hardware Installation and Replacement Guide
Chapter 3. Installing options and replacing hardware This chapter provides an introduction to the features and options that are avai
Installing internal options Important Read “Handling static-sensitive devices” on page 4 before opening the computer cover.Opening the
Accessing system board components and drives To access system board components and the drives: 1. Open the computer cover. See “Op
Installing adapter cards This section provides information and instructions for installing and removing PCI adapters. Your computer has
Internal drives are devices that your computer uses to read and store data. You can add drives to your computer to increase stora
Drive specifications Your computer comes with the following factory-installed drives: v An optical drive in bay 1 (some models) v
Installing a drive in bay 1 To install an optical drive in bay 1: 1. Open the computer cover. See “Opening the cover” on page
5. Slide the drive 3 into the bay until it locks in position. See Figure 10. 6. Pivot the drive-bay assembly upward to gai
What to do next: v To work with another option, go to the appropriate section. v To complete the installation, go to Chapter
3. Pivot the drive bay assembly upward to gain access to the cable connections and disconnect the drive bay cables. See Figure
8. Install the new drive 1 from the rear of the drive-bay assembly and slide the diskette-drive 1 to the locked position. S
ThinkCentre Hard ware Installation and Replacement Gui de
8. Restart the computer, leave it on for approximately 10 seconds. Turn off the computer by holding the power switch for approxi
Replacing the battery Your computer has a special type of memory that maintains the date, time, and settings for built-in features,
Replacing the power supply assembly Attention Do not open your computer or attempt any repair before reading the “Important safety i
6. Disconnect the power supply cables 1and 2 from the system-board connectors and from all drives. See Figure 19. 7. Remove
11. Check the position of the voltage-selection switch on the rear of the computer. Use a ballpoint pen to slide the switch, if
3. Remove the heat sink from the system board by pivoting the lever 1 securing the heat sink until it is fully in the up p
Replacing a hard disk drive Attention Do not open your computer or attempt any repair before reading the “Important safety informati
3. Unlatch the hard disk drive front retainers 1 and rotate the hard disk drive upwards and lift up to remove the hard disk
5. Remove the failing hard disk drive from the bracket by flexing the bracket. 6. Install the new drive, flex the bracket, an
2. Pivot the drive-bay-assembly upward to gain access to the optical drive. See Figure 26. 3. Disconnect the signal and power c
Note Before using this information and the product it supports, be sure to read and understand the Safety and Warranty Guide for t
7. Slide the optical-drive 2 to the locked position. 8. Connect the signal and power cables to the rear of the optical driv
4. Slide the diskette drive up and out of the drive bay assembly. See Figure 29. 5. Disconnect the flat cable from the rear
2. Pivot the drive-bay assembly upward to gain access to the system board. 3. Locate the memory connectors. See “Identifying
5. Position the replacement memory module over the memory connector. Make sure the notch 1 on the memory module aligns correctl
2. Rotate the adapter card retainer 1 to the open position to remove a failing adapter card or to add an adapter card. See
2. Pivot the drive-bay assembly upward to gain access to the fan assembly 1. See Figure 33. 3. Disconnect the fan-assembly ca
Replacing the keyboard Attention Do not open your computer or attempt any repair before reading the “Important safety information” in
connectors on the rear of your computer” on page 6. 4. Disconnect the failing mouse cable from the computer. 5. Connect the n
40 ThinkCentre Hardware Installation and Replacement Guide
Chapter 4. Completing the parts replacement After replacing the parts, you need to close the cover and reconnect cables, including t
Contents Figures . . . . . . . . . . . . . . .v Chapter 1. Important safety information 1 Chapter 2. Overview . . . . .
7. If you are replacing the system board or microprocessor, you must update (flash) the BIOS. See “Updating (flashing) BIOS from
Updating (flashing) BIOS from a diskette or CD-ROM Important Start the Setup Utility program to view your system information. See
video, the series of beeps will end, and the system will automatically turn off. Remove the diskette from the diskette drive. 12.
Chapter 5. Security features To help prevent hardware theft and unauthorized access to your computer, several security lock options a
What to do next: v To work with another option, go to the appropriate section. v To complete the installation, go to Chapter
Appendix. Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your
vary significantly. Some measurements may have been made on development-level systems and there is no guarantee that these measuremen
Index Aadapterconnectors 14 installing 14 audio-line-in connector 7 audio-line-out connector 7 Bbattery, replacing 23 bay 2 drive, installi
recoveryboot block 43 replacingbattery 23 hard disk drive 28 heat sink 26 resources, information 3 riser card 14 Ssafety information 1 s
iv ThinkCentre Hardware Installation and Replacement Guide
Part Number: 43C6692 Printed in USA (1P) P/N: 43C6692
Figures 1. Controls and connectors . . . . . . . . .5 2. Connector locations . . . . . . . . . .6 3. Component loc
vi ThinkCentre Hardware Installation and Replacement Guide
Chapter 1. Important safety information CAUTION: Before using this manual, it is important that you read and understand all the rela
Kommentare zu diesen Handbüchern