Lenovo 6528 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Computers Lenovo 6528 herunter. Lenovo 6528 User Manual Benutzerhandbuch

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 216
  • Inhaltsverzeichnis
  • FEHLERBEHEBUNG
  • LESEZEICHEN
  • Bewertet. / 5. Basierend auf Kundenbewertungen

Inhaltsverzeichnis

Seite 1 - Installation and User Guide

Installation and User GuideThinkServer TS200Machine Types: 6522, 6523, 6524, 6525, 6526, 6528, 6529, and 6530

Seite 2

Antes de instalar este producto, lea la información de seguridad.Läs säkerhetsinformationen innan du installerar den här produkten.Important:Each caut

Seite 3

1. Position the front end of the front-panel assembly in the channel above drivebay 1 on the left side of the chassis.2. Push the front-panel assembly

Seite 4

7. Squeeze the spring clips 1 on the sides of the front USB connector assemblyand pull the assembly out of the back of the housing.8. Carefully pull

Seite 5 - Contents

9. Reconnect the external cables and power cords; then, turn on the attacheddevices and turn on the server.Removing the rear adapter retention bracket

Seite 6

Removing the front adapter-retention bracketTo remove the front adapter-retention bracket, complete the following steps:1. Read the safety information

Seite 7 - Contents v

5. Disconnect the cables from the power-supply cage to the system board and allinternal components.6. Remove the four black screws that secure the pow

Seite 8

2. Install the four screws that secure the power-supply cage to the chassis.3. Connect the cables from the power-supply cage to the system board and a

Seite 9

CAUTION:When replacing the lithium battery, use only Part Number 33F8354 or anequivalent type battery recommended by the manufacturer. If your system

Seite 10

Removing a ServeRAID BR10-il controllerTo remove the ServeRAID BR10-il controller, complete the following steps:1. Read the safety information that be

Seite 11 - Safety ix

plastic standoff.3. Connect the signal cable to the SAS/SATA controller.4. Install and lock the side cover (see “Installing the side cover” on page 33

Seite 12

Attention: Some cluster solutions require specific code levels or coordinated codeupdates. If the device is part of a cluster solution, verify that th

Seite 13 - Safety xi

Statement 1:DANGERElectrical current from power, telephone, and communication cables ishazardous.To avoid a shock hazard:v Do not connect or disconnec

Seite 14

7. Press the ServeRAID-MR10i adapter firmly into the connector on the systemboard.8. Reconnect the cables to the new ServeRAID-MR10i adapter.Removing

Seite 15 - Safety xiii

1 Battery2 Battery carrier3 RAID adapter4 Connector for battery carrierb. Press the battery carrier into the connector on the ServeRAID adapte

Seite 16

2 PCI slot5. Press the ServeRAID-MR10is adapter firmly into the connector on the systemboard.6. Reconnect the cables to the new ServeRAID-MR10is ada

Seite 17 - Chapter 1. Introduction

To remove a non-hot-swap power supply, complete the following steps:1. Read the safety information that begins on page vii and “Installation guideline

Seite 18 - 1 Model and machine type

Installing a non-hot-swap power supplyThis procedure applies only to server models that have a non-hot-swap powersupply. See “Removing the hot-swap po

Seite 19 - Related documentation

Removing the microprocessor and fan sinkTo remove the microprocessor and fan sink, complete the following steps:1. Read the safety information that be

Seite 20

c. Tip the top of the fan sink toward the front of the server while you slide itaway from the lower flange of the retention module; then, remove it fr

Seite 21

Installing a microprocessor and fan sinkTo install the microprocessor, complete the following steps:1. Touch the static-protective package that contai

Seite 22

a. Make sure that the fan sink retention lever is in the fully open position.Important: Be careful when you handle the microprocessor and fan sink.Do

Seite 23 - Features and technologies

Note:v Read the Safety information on page vii.v Read the “Installation guidelines” on page 29.To replace damaged or contaminated thermal grease on th

Seite 24

Statement 2:CAUTION:When replacing the lithium battery, use only Part Number 33F8354 or anequivalent type battery. If your system has a module contain

Seite 25

Removing the system boardTo remove the system board, complete the following steps:1. Read the safety information that begins on page vii and “Installa

Seite 26 - Specifications

9. Remove the eight screws (seven in front and one in rear) 1 that secure thesystem board to the chassis.10. Slide the system board toward the front

Seite 27 - EasyManage

12. If you are instructed to return the system board, follow all packaginginstructions, and use any packaging materials for shipping that are supplied

Seite 28

5. Install the eight screws (seven in front and one in rear) that secure the systemboard to the chassis.6. Install any of the following components tha

Seite 29

108 ThinkServer TS200 Types 6522, 6523, 6524, 6525, 6526, 6528, 6529, and 6530: Installation and User Guide

Seite 30

Chapter 7. Configuring the serverThe following configuration programs come with the server:v Setup UtilityThe Setup Utility (formerly called the Confi

Seite 31 - Front view

Table 14. Server configurations and applications for configuring and managing RAIDarrays (continued)Server configurationRAID array configuration(befor

Seite 32 - 4 Power-on LED 9 USB 1

Utility, the changes are reflected in the system summary; you cannot changesettings directly in the system summary.– Product DataSelect this choice to

Seite 33

- Network ConfigurationSelect this choice to view the system management network interface port,the IMM MAC address, the current IMM IP address, and ho

Seite 34 - Rear view

v User SecuritySelect this choice to set, change, or clear passwords. See “Passwords” for moreinformation.This choice is on the full and limited Setup

Seite 35 - Microprocessor

Statement 3:CAUTION:When laser products (such as CD-ROMs, DVD drives, fiber optic devices, ortransmitters) are installed, note the following:v Do not

Seite 36

password has access to only the limited Setup Utility menu; the user can set,change, and delete the power-on password, if the system administrator has

Seite 37

RAID controllersThe following table lists the various utilities available to configure RAID controllersbefore an operating system is installed.Table 1

Seite 38 - System-board LEDs

1. After you turn on the power and when the computer is starting, you areprompted to press Ctrl + H when the following message is displayed:Copyright©

Seite 39

New ConfigurationClears the existing configuration and lets you create a newconfiguration.Add ConfigurationRetains the existing storage configuration

Seite 40 - Power-supply LEDs

The EasyStartup program has the following features:v Self-booting DVDv Easy-to-use, language-selectable interfacev Integrated help systemv Automatic h

Seite 41 - 5 Power LED

If you continue to the main program interface, you will have the following selectableoptions:v Compatibility notes: This selection provides informatio

Seite 42 - Turning on the server

– Integrated Mirroring Enhanced (IME) with hot-spare support (also known asRAID 1E)Use this option to create an integrated mirror enhanced array of th

Seite 43

4. To highlight the drive that you want to format, use the Up Arrow and DownArrow keys. To scroll left and right, use the Left Arrow and Right Arrow k

Seite 44 - Turning off the server

v Save response file: This task gives you the option of saving the information ona diskette or USB device as a response file for future installations

Seite 45 - Installation guidelines

v SAS firmware is stored in ROM on the integrated RAID controller on the systemboard.v Major components contain vital product data (VPD) code. You can

Seite 46 - System reliability guidelines

Statement 4:≥ 18 kg (39.7 lb.) ≥ 32 kg (70.5 lb.) ≥ 55 kg (121.2 lb.)CAUTION:Use safe practices when lifting.Statement 5:CAUTION:The power control but

Seite 47

The IMM supports the following basic system management features:v Environmental monitor with fan speed control for temperature, voltages, fanfailure,

Seite 48 - Removing the side cover

identify the server, and perform other management functions. Any standard Telnetclient application can access the SOL connection.Using the remote pres

Seite 49 - Installing the side cover

2. On the Login page, type the user name and password. If you are using the IMMfor the first time, you can obtain the user name and password from your

Seite 50 - Removing the two-piece bezel

v The server is not a domain controller. However, it is recommended to have theserver join a domain.v The account that you use to log in and to instal

Seite 51

v ASP.NETv ASPv CGIv Server Side Includesv Windows Authenticationv IIS 6 Metabase CompatibilityNote: When you select ASP.Net or ASP, a dialog box disp

Seite 52 - Installing the lower bezel

Chapter 8. TroubleshootingThis chapter describes the diagnostic tools that are available to help you solveproblems that might occur in the server.If y

Seite 53 - Removing a memory module

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the parts listing in the Ha

Seite 54 - Installing a memory module

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the parts listing in the Ha

Seite 55 - Unbuffered DIMMs (UDIMMs)

Keyboard, mouse, or pointing-device problemsv Follow the suggested actions in the order in which they are listed in the Action column until the proble

Seite 56 - Registered DIMMs (RDIMMs)

Memory problemsv Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the parts li

Seite 57

Statement 8:CAUTION:Never remove the cover on a power supply or any part that has the followinglabel attached.Hazardous voltage, current, and energy l

Seite 58 - Third pair of DIMMs 3, 6

Microprocessor problemsv Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the

Seite 59

Monitor problemsSome monitors have their own self-tests. If you suspect a problem with yourmonitor, see the documentation that comes with the monitor

Seite 60 - Removing a DVD drive

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the parts listing in the Ha

Seite 61 - Installing a DVD drive

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the parts listing in the Ha

Seite 62

Power problemsv Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the parts lis

Seite 63 - Removing a tape drive

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the parts listing in the Ha

Seite 64 - Installing a tape drive

Software problemsv Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the parts

Seite 65 - 3 Drive retainer clip

2. Check for loose cables in the power subsystem. Also check for short circuits, forexample, if a loose screw is causing a short circuit on a circuit

Seite 66 - 1 Drive-tray assembly

Solving undetermined problemsIf the diagnostic tests did not diagnose the failure or if the server is inoperative, usethe information in this section.

Seite 67

v System-event log: This log contains all IMM, POST, and system managementinterrupt (SMI) events. You can view the system-event log through the SetupU

Seite 68

DANGEROverloading a branch circuit is potentially a fire hazard and a shock hazardunder certain conditions. To avoid these hazards, ensure that your s

Seite 69

4. Click Downloads and drivers to download firmware updates.If IPMItool is installed in the server, you can use it to view the system-event log.Most r

Seite 70

POST error codesWhen you turn on the server, it performs a series of tests to check the operation ofthe server components and some optional devices in

Seite 71 - Removing an adapter

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

Seite 72

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

Seite 73 - Installing an adapter

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

Seite 74

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

Seite 75 - Removing a PCI card

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

Seite 76 - Installing a PCI card

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

Seite 77

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

Seite 78 - 4 Virtual media key (front)

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

Seite 79 - 1 Mounting bracket (rear)

Chapter 1. IntroductionThis Installation and User Guide is intended to use with your Lenovo®ThinkServer™TS200 (Machine Types 6522, 6523, 6524, 6525, 6

Seite 80

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

Seite 81

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

Seite 82 - 2 Hot-swap power supply

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

Seite 83 - Completing the installation

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

Seite 84

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

Seite 85

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

Seite 86 - Reinstalling the side cover

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

Seite 87 - Connecting external devices

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

Seite 88

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

Seite 89 - Removing the rear system fan

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

Seite 90

1 Model and machine typeFor a list of supported optional devices for the server, go tohttp://www.lenovo.com/thinkserver and click the Options tab.No

Seite 91 - 2 Hard disk drive cage

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

Seite 92 - 3 Slot

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

Seite 93

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

Seite 94

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

Seite 95 - 5 Retaining latch

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

Seite 96

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

Seite 97 - 4 Drive cage release tab

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

Seite 98

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

Seite 99

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

Seite 100

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

Seite 101

Related documentationThe Lenovo ThinkServer Documentation DVD contains documentation for theserver in Portable Document Format (PDF). The Lenovo Think

Seite 102

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

Seite 103

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

Seite 104

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the ″Parts Listing″ section

Seite 105 - Installing the battery

Note: After you exit from the stand-alone memory diagnostic environment, youmust restart the server to access the stand-alone memory diagnosticenviron

Seite 106 - Removing and replacing FRUs

To save the DSA log to a file on a diskette or to the hard disk, click Save Log onthe diagnostic programs screen and specify a location and name for t

Seite 107

Appendix A. Getting help and technical assistanceIf you need help, service, or technical assistance or just want more informationabout Lenovo products

Seite 108

Calling for serviceDuring the warranty period, you can get help and information by telephone throughthe Customer Support Center.These services are ava

Seite 109 - 3 RAID adapter

Service methods and procedures vary by country, and some services might not beavailable in all countries. International Warranty Service is delivered

Seite 110

182 ThinkServer TS200 Types 6522, 6523, 6524, 6525, 6526, 6528, 6529, and 6530: Installation and User Guide

Seite 111 - 1 ServeRAID-MR10is

Appendix B. NoticesLenovo may not offer the products, services, or features discussed in this documentin all countries. Consult your local Lenovo repr

Seite 113

4 ThinkServer TS200 Types 6522, 6523, 6524, 6525, 6526, 6528, 6529, and 6530: Installation and User Guide

Seite 114

estimated through extrapolation. Actual results may vary. Users of this documentshould verify the applicable data for their specific environment.Trade

Seite 115

Lenovo makes no representation or warranties regarding non-Lenovo products andservices, including but not limited to the implied warranties of merchan

Seite 116

L’etiquette du système respecte la Directive européenne 2002/96/EC en matière deDéchets des Equipements Electriques et Electroniques (DEEE), qui déter

Seite 117

Table 17. Limits for particulates and gases (continued)Contaminant Limits1ASHRAE 52.2-2008 - Method of Testing General Ventilation Air-Cleaning Device

Seite 118 - Thermal grease

Battery return programThis product may contain a lithium or lithium ion battery. Consult your user manualor service manual for specific battery inform

Seite 119

batteries pour indiquer que la batterie ne doit pas être mise au rebut mais plutôtrécupérée en fin de cycle de vie selon cette norme.In accordance wit

Seite 120 - Removing the system board

This device complies with Part 15 of the FCC Rules. Operation is subject to thefollowing two conditions: (1) this device may not cause harmful interfe

Seite 121

Dieses Produkt entspricht den Schutzanforderungen der EU-Richtlinie 2004/108/EG(früher 89/336/EWG) zur Angleichung der Rechtsvorschriften über dieelek

Seite 122 - Installing the system board

Japan Voluntary Control Council for Interference (VCCI) statementTaiwan Class A warning statementPeople’s Republic of China Class A warning statementK

Seite 123

IndexAacoustical noise emissions 11adapterhot-plug devices 92installing 57hot-plug 92PCI cardinstalling 60removing 55requirements 57scanning order 57S

Seite 124

Chapter 2. Server setup roadmapThe installation process varies depending on the configuration of the server when itwas delivered. In some cases, the s

Seite 125

diskette drive (continued)removing 44display problems 135documentation DVD 3drivecables 54removable-media 47, 48drive bays, internal 43drivesbay 1, 2,

Seite 126 - Setup Utility menu choices

HH8 heartbeat LED 24handling static-sensitive devices 31hard disk drivediagnostic tests, types of 131formatting 120problems 130status LED 17hard disk

Seite 127

LEDs (continued)rear of server 18LEDs and controlson the front of the server 15logssystem-event message 144lower bezelinstalling 69removing 34LSI Conf

Seite 128

reliability 12remote presence featurefunctions 8using 125removingadapter 55battery 89CD drive 44connector 62cover 32DIMMs 37diskette drive 44DVD drive

Seite 129 - Passwords

system board (continued)removing 104switches and jumpers 21system reliability guidelines 30system-board error LED 23system-error LED 17system-event lo

Seite 132

6 ThinkServer TS200 Types 6522, 6523, 6524, 6525, 6526, 6528, 6529, and 6530: Installation and User Guide

Seite 133

Chapter 3. What is included with your serverThe TS200 server package includes the server, power cords, the ThinkServerDocumentation DVD, and software

Seite 134 - Setup and configuration

v Remote presence capability and blue-screen captureThe remote presence feature provides the following functions:– Remotely viewing video with graphic

Seite 135 - Configuring RAID

The command-line interface provides direct access to server managementfunctions through the IPMI 2.0 protocol. Use the command-line interface to issue

Seite 136 - Formatting a hard disk drive

SpecificationsThe following information is a summary of the features and specifications of theserver. Depending on the server model, some features mig

Seite 137

Table 2. Features and specifications (continued)RAID controllers:v ServeRAID BR10ilv ServeRAID-MR10iv ServeRAID-M1015v ServeRAID M5015v ServeRAID MR10

Seite 138 - Updating the firmware

Reliability, availability, and serviceabilityThree important server design features are reliability, availability, and serviceability(RAS). The RAS fe

Seite 139

v Wake on LAN capabilityChapter 3. What is included with your server 13

Seite 140

ThinkServer TS200 Types 6522, 6523, 6524, 6525,6526, 6528, 6529, and 6530Installation and User Guide

Seite 141

14 ThinkServer TS200 Types 6522, 6523, 6524, 6525, 6526, 6528, 6529, and 6530: Installation and User Guide

Seite 142 - Installation requirements

Chapter 4. Server controls, LEDs, and powerThis section describes the controls and light-emitting diodes (LEDs) and how to turnthe server on and off.F

Seite 143 - Installation order

1 Simple-swap hard disk drive 6 Hard disk drive activity LED2 DVD drive activity LED (green) 7 System error LED3 Front information panel 8

Seite 144

Fading on and off: The server is in a reduced-power state. To wake the server,press the power-control button or use the IMM Web interface. See “Loggin

Seite 145 - Chapter 8. Troubleshooting

Rear viewThe following illustration shows the connectors and LEDs on the rear of the server.1 USB 3 and 4 5 Serial (Com1)2 USB 1 and 2 6 Power

Seite 146 - Hard disk drive problems

System-board internal connectorsThe following illustrations show the internal connectors and switches on the systemboard.MicroprocessorHeatsinkOrienta

Seite 147 - Intermittent problems

1 DIMM 1 11Fan 1 connector 21Slot 2: PCIe2 x8, 25w2 DIMM 2 12Hard disk backplaneconfigurationconnector22Slot 1: PCIe2 x8, 25w3 DIMM 3 1

Seite 148

3 Ethernet connector 1 7 SW1 (NMI button)4 USB connectors 1 and 2System-board switches and jumpersThe following illustration shows the switches

Seite 149 - Memory problems

Important:1. Before you change any switch settings or move any jumpers, turn off the server;then, disconnect all power cords and external cables. Revi

Seite 150 - Microprocessor problems

Table 4. System-board LEDs (continued)LED DescriptionBaseboard managementcontroller heartbeat LEDThis LED flashes to indicate that the IMM is function

Seite 151 - Monitor problems

Note: Before using this information and the product it supports, read the general information in Appendix B, “Notices,” on page 183and the Warranty an

Seite 152 - Optional-device problems

v Follow the suggested actions in the order in which they are listed in the Action column until the problemis solved.v See the parts listing in the Ha

Seite 153

1 AC power LED2 DC power LED3 Fault LED4 Fault LED5 Power LEDThe following table describes the problems that are indicated by variouscombina

Seite 154 - Power problems

Table 5. Power-supply LEDsPower-supply LEDsDescription Action NotesAC DC ErrorOff Off Off No ac power tothe server or aproblem with theac power source

Seite 155 - Serial port problems

the server is connected to ac power, the power-control button becomes active (thepower-on LED flashes slowly). You can turn on the server by pressing

Seite 156 - Solving power problems

Turning off the serverWhen you turn off the server and leave it connected to ac power, the server canrespond to requests to the service processor, suc

Seite 157

Chapter 5. Installing and replacing optional devicesThis chapter provides detailed instructions for installing optional hardware devices inthe server.

Seite 158 - Event logs

devices. However, you must turn off the server before performing any steps thatinvolve removing or installing adapter cables or non-hot-swap optional

Seite 159

v Avoid wearing loose-fitting clothing on your forearms. Button long-sleeved shirtsbefore working inside the server; do not wear cuff links while you

Seite 160 - System-event log

Server componentsThe following illustration shows the major components in the server.1 Cover 10 SATA hard disk drive (some models)2 Non-hot-swap

Seite 161 - POST error codes

Attention: Operating the server for more than 30 minutes with the side coverremoved might damage server components. For proper cooling and airflow, re

Seite 162

ContentsSafety ...viiChapter 1. Introduction ...1Notices and statements in this document...2R

Seite 163

3. Position the lip on the bottom edge of the side cover on the ledge on the bottomof the chassis; then, rotate the cover up to the chassis. Press dow

Seite 164

5. Lift the lower bezel to disengage the two bottom tabs from the chassis. Set thelower bezel aside.Chapter 5. Installing and replacing optional devic

Seite 165

6. Carefully pull the two bezel clips 1 on the left side of the upper bezel awayfrom the chassis; then, rotate the upper bezel to the right side of

Seite 166

2. Rotate the top of the lower bezel up to the chassis; then, press the blue releasetab on the right side of the lower bezel and completely close the

Seite 167

6. If you are instructed to return the DIMM, follow all packaging instructions, anduse any packaging materials for shipping that are supplied to you.I

Seite 168 - User’s Guide on the Web

where:ggg is the total capacity of the DIMM (for example, 1GB, 2GB, or 4GB)e is the number of ranks1 = single-rank2 = dual-rank4 = quad-rankff is the

Seite 169

v The following table lists the supported UDIMM population.Table 6. Supported UDIMM population per channelDIMMs slotsper channelDIMMs installedin each

Seite 170

v The following table lists the supported RDIMM population.Table 9. Supported RDIMM population per channelDIMMs slotsper channelDIMMs installedin each

Seite 171

To install a DIMM, complete the following steps:1. Read the safety information that begins on page vii and “Installation guidelines”on page 29.2. Turn

Seite 172

If you have other devices to install or remove, do so now; otherwise, go to“Completing the installation” on page 67.Removing and installing internal d

Seite 173

Power and signal cables for internal drives ...54Removing an adapter ...55Installing an adapter ...57

Seite 174

The following notes describe the types of drives that the server supports and otherinformation that you must consider when installing a drive:v Make s

Seite 175

1 Release buttons2 Drive retainer clip7. Remove the drive retainer clip from the side of the drive. Save the clip to usewhen you install the repla

Seite 176

Statement 3:CAUTION:When laser products (such as CD-ROMs, DVD drives, fiber optic devices,or transmitters) are installed, note the following:v Do not

Seite 177

1 Release buttons2 Drive retainer clip5. Push the drive into the bay.6. Connect the power and signal cables to the drive.Note: Route the signal ca

Seite 178

1 EMC shield2 Tape drive3 Drive retainer clip9. If you are instructed to return the drive, follow all packaging instructions, anduse any packagi

Seite 179

8. Set any jumpers or switches on the drive according to the documentation thatcomes with the drive.9. Remove the drive retainer clip from the side of

Seite 180

To remove a hot-swap hard disk drive, complete the following steps:1. Read the safety information that begins on page vii and “Installation guidelines

Seite 181

Table 13. IDs of the hot-swap drives (models with four drive bays)Drive bay ID40516273Installing a hot-swap hard disk driveThis procedure applies only

Seite 182

1. Touch the static-protective package that contains the drive to any unpaintedmetal surface on the server; then, remove the drive from the package an

Seite 183

Removing a simple-swap hard disk driveThis procedure applies only to server models that have simple-swap SATA hard diskdrives.Attention: Simple-swap h

Seite 184

Starting the Setup Utility ...110Setup Utility menu choices ...110Passwords ...113Using the Boo

Seite 185

Installing a simple-swap hard disk driveThis procedure applies only to server models that have simple-swap SATA hard diskdrives.Attention: Simple-swap

Seite 186

v The drives that are preinstalled in the server come with power and signal cablesattached. If you replace any drives, remember which cable is attache

Seite 187

7. Remove the expansion-slot screw 2 at the rear of the adapter 3 if any.8. Carefully grasp the adapter by its top edge or upper corners. And pull

Seite 188

Installing an adapterThe following notes describe the types of adapters that the server supports andother information that you must consider when you

Seite 189

6. Remove the screw that secures the expansion-slot cover to the chassis. Storethe expansion-slot cover and screw in a safe place for future use.Note:

Seite 190

8. If you are installing a full-length adapter, remove the blue adapter guide (if any)from the end of the adapter.1 Adapter guide9. Carefully grasp

Seite 191

Attention: To avoid breaking the retaining clips or damaging the adapterconnector, open and close the clips gently.5. Carefully grasp the end of the a

Seite 192

9. Take the other end of the signal cable that is attached to the drive backplanesection for drive bays 0 through 3 (as labeled on the front of the dr

Seite 193 - Viewing the test log

5. Align the flash device with the connector on the system board and push it intothe connector until it is firmly seated.6. Press down on the retainin

Seite 194 - Diagnostics messages

4. If you are instructed to return the virtual media key, follow all packaginginstructions, and use any packaging materials for shipping that are supp

Seite 195 - Using the documentation

Diagnostics messages...178Appendix A. Getting help and technical assistance ...179Before you call ...179

Seite 196 - Using other services

Removing a hot-swap power supplyThis procedure applies only to server models that have hot-swap power supplies.See “Installing a non-hot-swap power su

Seite 197 - Lenovo product service

To remove a hot-swap power supply, complete the following steps:1. Read the safety information that begins on page vii and “Installation guidelines”on

Seite 198

1 Release lever2 Hot-swap power supply2. Using the handle, push the power supply toward the front of the chassis until itlocks into place.3. Conne

Seite 199 - Appendix B. Notices

4. Thread the cable through the rope clip and around an object that is not part ofor permanently secured to the building structure or foundation, and

Seite 200 - Important notes

68 ThinkServer TS200 Types 6522, 6523, 6524, 6525, 6526, 6528, 6529, and 6530: Installation and User Guide

Seite 201 - Appendix B. Notices 185

2. Install the lower bezel:a. Insert the two bottom tabs on the lower bezel into the matching holes in thefront of the chassis.b. Rotate the top of th

Seite 202 - Particulate contamination

Reinstalling the side coverIf you removed the side cover, reinstall it.Note: The rear adapter-retention bracket rests against the server side cover. Y

Seite 203 - Hazardous Substances

Connecting the cablesAttention: To prevent damage to equipment, connect the power cords last.If the server cables and connector panel have color-coded

Seite 204 - Battery return program

72 ThinkServer TS200 Types 6522, 6523, 6524, 6525, 6526, 6528, 6529, and 6530: Installation and User Guide

Seite 205 - Electronic emission notices

Chapter 6. Installing and replacing customer replaceable unitsRemoving the rear system fanAttention:v Replace a failed fan within 48 hours.v To ensure

Seite 206

SafetyBefore installing this product, read the Safety Information.Antes de instalar este produto, leia as Informações de Segurança.Pred instalací toho

Seite 207 - Appendix B. Notices 191

Installing the rear system fanAttention:v Replace a failed fan within 48 hours.v To ensure proper cooling and airflow, do not operate the server for m

Seite 208

Removing the hard disk drive fan assemblyThis procedure applies only to server models that have a hard disk drive fanassembly.Attention:v Replace a fa

Seite 209

9. Pull out on the hard disk drive fan assembly release tabs; then, rotate theassembly away from the drive cage slightly.1 Release tabs2 Hard disk

Seite 210

1 Release tabs2 Hard disk drive fan assembly3 Slot2. Route the hard disk drive signal and power cables through the slots on theedge of the hard

Seite 211 - Index 195

5. Connect the hard disk drive fan assembly cable to the system board (see“System-board internal connectors” on page 19 for the location of the hard d

Seite 212

1 Retaining tab2 Drive cage release tab3 Locating pins4 Simple-swap backplate5 Retaining latch11. Lift the simple-swap backplate out of the

Seite 213 - Index 197

1 Retaining tab2 Drive cage release tab3 Locating pins4 Simple-swap backplate5 Retaining latch2. Tilt the top of the simple-swap backplate t

Seite 214

Removing the SAS/SATA hard disk drive backplaneThis procedure applies only to hot-swap server models with a SAS/SATA hard diskdrive backplane installe

Seite 215

10. Tilt the top of the hard disk drive backplane away from the drive cage until it isclear of the locating pins.11. Lift the SAS/SATA hard disk drive

Seite 216 - Printed in USA

6. Install the hard disk drive fan assembly onto the hard disk drive cage (see“Installing the hard disk drive fan assembly” on page 76).7. Install the

Verwandte Modelle: 6526 | 6529 | 6524 | 6530 | 6525 | 6522 |

Kommentare zu diesen Handbüchern

Keine Kommentare